The diesel generator controller system consists of magneto, low-voltage cable, incineration coil, high-voltage cable The structure and device of magneto are composed of spark plug and incineration switch. The magneto system is contactless. In the process of working, there is no spark to meet the explosion-proof requirements. The output electric pressure is 160-180v DC). From the direction of a, the rotation direction of the driving wheel is counterclockwise. The driving wheel of the generator control module rolls for three turns to complete an operating cycle of the engine, that is, the speed ratio between it and the crankshaft is 1.5:1 supplied by the diesel generator set The low-voltage electric energy is stored in the capacitor 7. When the rotating punctual distribution arm 6 driven by the reduction gear passes through the sensor coil, it will excite the SCR electronic switch in order to transfer the energy of the electric container to the incineration coil. The resulting high-voltage electricity will cause the spark plug to jump. Before starting the magneto of the controller device, the flywheel must be rolled to make the top cylinder 32 crankshaft angle magnetoelectricity before the top dead center of the incineration advance angle azimuth An investigation hole is set at the tail end of the machine to see the red line symbol rotating with the shaft and the red line symbol under the white CCW word on the shell, and then roll the drive disk of the magneto to make the two red line symbols into a straight line. The generator unit controller can install the magneto and tighten the two screws connected with the transmission device. At this time, the incineration advance angle is an approximate value and an accurate adjustment method of the incineration advance angle

松开磁电机与传动装置的两个螺钉发电机控制屏磁电机可沿传动轴线滚动发电机电子调速器磁电机由中间方位向自由端方向滚动至大的方位时焚烧提早角滞后约10曲轴转角左右反之向输出端滚动至大方位时柴油发电机组控制器焚烧提早角提早约10曲轴转角左右柴油发电机工作时衔接磁电机的2个螺钉要确保拧紧

Loosen the two screws between the magneto and the transmission device. The magneto on the generator control panel can roll along the transmission axis. When the magneto of the generator electronic governor rolls from the middle direction to the free end to the maximum direction, the incineration advance angle lags about 10 crankshaft angle. On the contrary, when rolling to the output end to the maximum direction, the incineration advance angle of the diesel generator set controller is about 10 crankshaft angle Ensure that the two screws connecting the magneto are tightened when the oil generator is working

磁电机装上低压电缆插头引出14根低压电线每根电线均标示不同符号依照发火次序与每个气缸的焚烧线圈+极联接符号N的电线与每排缸的焚烧线圈一极串联而且两排缸并联符号G的电线与焚烧开关衔接其接线方法为发电机配件断路时发动机工作接地时则发动机停车

The magneto is equipped with a low-voltage cable plug to lead out 14 low-voltage wires. Each wire is marked with different symbols. According to the firing order, it is connected with the incineration coil + pole of each cylinder. The wire of symbol n is connected in series with one pole of the incineration coil of each row of cylinders, and the wire of symbol g in parallel of the two rows of cylinders is connected with the incineration switch. The wiring method is that the engine stops when the generator accessories are open circuit and the engine is grounded

低压电缆经过低压电缆把磁电机输出的电能传递到焚烧线圈不同类型的磁电机要配相应标准的低压电缆由插头引出的一股电缆内每根电线均标示不同的符号根据发动机的发火次序把每根电线衔接到对应气缸的焚烧线圈的正极、负极焚烧开关及接地等

The low-voltage cable transmits the electric energy output by the magneto to the incineration coil through the low-voltage cable. Different types of magnetos shall be equipped with corresponding standard low-voltage cables. Each wire in a cable led out from the plug shall be marked with different symbols. Each wire shall be connected to the positive and negative incineration switches and grounding of the incineration coil of the corresponding cylinder according to the ignition sequence of the engine

焚烧线圈焚烧线圈将磁电机输出的低压电转变为高压电发电机调速器不同类型的磁电机应配相应标准的焚烧线圈本机所用焚烧线圈高输出电压为40000VDC)当输出电压为10000V时火花塞跳火持续时间为550微秒正、负南北极与电线联接时要把螺帽拧紧

Incineration coil incineration coil converts the low-voltage power output by the magneto into high-voltage electric generator governor. Different types of magneto shall be equipped with corresponding standard incineration coil. The maximum output voltage of the incineration coil used by this machine is 40000 VDC). When the output voltage is 10000 V, the duration of spark plug ignition is 550 microseconds. When the positive and negative south north poles are connected with the wire, tighten the nut

火花塞火花塞螺纹为M18×1.5mm装入缸头时其扭紧力矩为42-52N.m拧紧后应确保火花塞底部的螺纹端面与缸盖底面平齐火花塞空隙为0. 6mm当空隙值增大到0.89mm时火花塞将呈现失火现象使发动机工作不稳甚至停车发电机控制器要求按不同的运用条件定时查看火花塞清除火花塞及其螺纹处呈现的积炭

Spark plug the spark plug thread is M18 × When 1.5mm is installed into the cylinder head, the tightening torque is 42-52n. M. after tightening, ensure that the threaded end face at the bottom of the spark plug is flush with the bottom of the cylinder head. The gap of the spark plug is 0.6mm. When the gap value increases to 0.89mm, the spark plug will show misfire, making the engine unstable and even stopping the generator. The controller requires to regularly check the spark plug according to different application conditions and remove the carbon deposits at the spark plug and its threads