上次给大家讲了合金尾气发电机组的冷却液作用，大家都知道冷却液久了呢都需要更换，而且半年内至少更换一次，以避免由于冷却系统内有沉淀而降低冷却性能。更换冷却液的另一个原因是避免机组锈蚀的危险，因为时间一长，锈迹就会降低添加剂的有效性及使水温传感器失效。那更换合金尾气发电机组冷却液有什么注意事项吗？今天合金尾气发电机组厂家就给大家分享一下：

　　Last time I talked to everyone about the role of the coolant in the alloy tail gas generator set. As we all know, the coolant needs to be replaced over time, and it should be replaced at least once every six months to avoid a decrease in cooling performance due to sedimentation in the cooling system. Another reason for replacing the coolant is to avoid the danger of rusting the unit, as over time, rust will reduce the effectiveness of additives and cause the water temperature sensor to fail. Are there any precautions for replacing the coolant of the alloy tail gas generator set? Today, the manufacturer of alloy tail gas generator sets will share with you:

　　机组长期存放时一定要放尽机体及冷却系统其它附件中的冷却液。冷却液排放前，确保机组关闭及机体完全冷却。一般要求放尽水箱、机体、水泵（如有放水口）、机油冷却器（如有放水口）、水加热器（如有放水口）、滤清器中的水。更换冷却液时，冷却系统应先用清水冲洗,清洗时一定要等冲出的水很干净时才行。 确保合金尾气停机和完全冷却后，才能加入冷却液。当发动机温度依然很高时，不要打开加水口盖。否则蒸气或高温冷却液可能会喷出。

　　When storing the unit for a long time, it is necessary to drain all the coolant in the body and other accessories of the cooling system. Before discharging the coolant, ensure that the unit is turned off and the body is completely cooled. It is generally required to drain all water from the water tank, machine body, water pump (if any), oil cooler (if any), water heater (if any), and filter. When replacing the coolant, the cooling system should be rinsed with clean water first. When cleaning, be sure to wait until the water flushed out is very clean. Ensure that the alloy exhaust is shut down and completely cooled before adding coolant. Do not open the water inlet cap when the engine temperature is still high. Otherwise, steam or high-temperature coolant may spray out.

　　此外向合金尾气发电机组水箱中添加冷却液还须注意如下事项：

　　In addition, the following precautions should be taken when adding coolant to the water tank of the alloy tail gas generator set:

　　1、 向冷却系统加入冷却液前，要确保其排放盖紧闭及排放塞位于正确位置

　　1. Before adding coolant to the cooling system, ensure that the drain cap is tightly closed and the drain plug is in the correct position

　　2、 向系统加入冷却液时不要太快，以避免系统内形成气泡断层

　　2. Do not add coolant to the system too quickly to avoid the formation of bubbles and faults in the system

　　3、 空气须通过通风口或通过填孔排出。如冷却系统连接有加热器，加热器控制阀须打开，注入时应保持单元内通风

　　3. Air must be discharged through ventilation openings or through filling holes. If the cooling system is connected to a heater, the heater control valve must be opened, and ventilation should be maintained inside the unit during injection

　　4、注入冷却液时，液面应达到位于填口塞焊接面下5厘米处

　　4. When injecting coolant, the liquid level should reach 5 centimeters below the welding surface of the filler plug

　　5、冷却液加好后，应注意启动并预热机组。同时检查冷却液面，如需要，请补满。

　　5. After adding the coolant, pay attention to starting and preheating the unit. At the same time, check the coolant level and fill it up if necessary.

　　好了，关于合金尾气发电机组更换冷却液的注意事项就给大家分享这么多，如果遇到问题可咨询我们。

　　Alright, that's all for the precautions on replacing the coolant for the alloy tail gas generator set. If you encounter any problems, please feel free to consult us.

　　本文由  合金尾气发电机组 友情奉献.更多有关的知识请点击  https://www.huannengpower.cn/   真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from the alloy tail gas generator set For more related knowledge, please click https://www.huannengpower.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.